Owner guide · Toyota of Fox Lake · Fox Lake, IL

Toyota Sienna Headlight Bulb Guide

What the Sienna uses for headlights, the three bulbs you can replace yourself, their bulb numbers and wattage, how to change them and how the headlight controls work, from Toyota's 2026 Sienna owner's manual (OM08082U), read November 16, 2026. Owners of other model years should check the manual for their Sienna.

Toyota Sienna minivan with LED headlights on a suburban street
Toyota Sienna. Manufacturer image, illustrative
LEDHeadlights, dealer replaced
3Bulbs you can replace
WY21WRear turn signal bulb
20 minBattery-saving light off

What headlight bulb does a Toyota Sienna use?

For the 2026 Sienna, none you can buy and swap yourself. Toyota's 2026 Sienna owner's manual (OM08082U) lists the headlights among the lights that need to be replaced by your Toyota dealer, and says the lights other than the rear turn signal lights, back-up lights and license plate lights each consist of a number of LEDs. Those three are the bulbs with do-it-yourself steps: WY21W, W16W and W5W.

Sienna exterior light bulb numbers and wattage

LightBulb No.WattsType
Rear turn signal lightsWY21W21Wedge base bulb (amber)
Back-up lightsW16W16Wedge base bulb (clear)
License plate lightsW5W5Wedge base bulb (clear)

From the Light bulbs table in Toyota's 2026 Sienna owner's manual (OM08082U), page 692, read November 16, 2026. The table lists no headlight bulb.

Lights your Toyota dealer replaces

The manual (page 598) lists these Sienna lights as ones that need to be replaced by your Toyota dealer:

  • Headlights
  • Daytime running lights
  • Front turn signal/parking lights
  • Front side marker lights
  • Side turn signal lights
  • Tail lights
  • Stop lights
  • Fog lights (if equipped)
  • Rear side marker lights
  • High mounted stoplight
  • Outer foot lights (if equipped)

The manual explains that the lights other than the rear turn signal lights, back-up lights and license plate lights each consist of a number of LEDs. If any of the LEDs burn out, it says to take the vehicle to your Toyota dealer to have the light replaced. Temporary condensation on the inside of a light lens does not indicate a malfunction; contact your Toyota dealer if large drops of water have built up on the inside of the lens or water has built up inside the light.

Replacing a Sienna rear turn signal bulb

The manual says the difficulty of replacement varies by bulb and to check the wattage of the bulb to be replaced first. Its steps for the rear turn signal lights are:

  1. Open the back door.
  2. Remove the securing screws and remove the unit, pulling the lamp assembly directly backward from the rear of the vehicle.
  3. Turn the bulb base counterclockwise.
  4. Remove the light bulb and install a new light bulb.
  5. Install the bulb base in the light unit by inserting it and turning it clockwise.
  6. Align the grooves on the light unit with the claws and insert the unit straight so the pin fits into the hole. Confirm the unit is completely secured, then reinstall the screws.

For the back-up lights, the manual says to open the back door and remove the cover (wrap the screwdriver tip with a rag to prevent damage), turn the bulb base counterclockwise, replace the bulb, reinstall the bulb base by turning it clockwise and reinstall the cover. For the license plate lights, remove the cover with a flathead screwdriver and the lens with a small flathead screwdriver (wrap the tips with tape), replace the bulb, refit the lens on its hooks and install the cover. If a replacement seems difficult to perform, the manual says to contact your Toyota dealer.

Before you change a Sienna bulb

Toyota recommends genuine Toyota products designed for the vehicle when replacing light bulbs: because certain bulbs are connected to circuits designed to prevent overload, non-genuine parts or parts not designed for this vehicle may be unusable. The manual's warnings include:

  • Turn off the light and do not replace the bulb right after turning it off. The bulb becomes very hot and may cause burns.
  • Do not touch the glass portion of the bulb with bare hands. If you must hold it, use a clean dry cloth. A scratched or dropped bulb may blow out or crack.
  • Fully install the bulb and any parts used to secure it, and make sure the bulb is fully seated and locked, to prevent heat damage, fire or water entering the light unit.
  • Check the wattage of the bulb before installing it to prevent heat damage.
  • Do not attempt to repair or disassemble light bulbs, connectors, electric circuits or component parts. Doing so may result in death or serious injury due to electric shock.

If the lights do not turn on even after a fuse has been replaced, the manual (page 596) says a bulb may need replacement. If the replaced fuse blows again, have the vehicle inspected by your Toyota dealer.

How the Sienna headlights work

The headlight switch has an AUTO position: the headlights, daytime running lights and the other lights the switch controls turn on and off automatically. AUTO mode can be used when the power switch is in ON. The manual says the headlight control sensor may not function properly if an object is placed on it or anything that blocks it is affixed to the windshield. On vehicles with windshield wiper linked headlight illumination (if equipped), using the windshield wipers while driving in daytime, with the headlight switch in the position the manual shows, turns the headlights on automatically after several seconds.

Daytime running lights turn on automatically when the hybrid system is operating, the parking brake is released, the headlight switch is in a qualifying position and the fog lights are not on. Depending on the headlight type, they use the low beam headlights at reduced brightness or the parking lights at higher brightness. In the U.S., they can be turned off with the switch, and the manual says they are not designed for use at night.

With the headlights on, push the lever away from you for high beams; pull it toward you to the center position to turn them off. Pull the lever toward you and release it to flash the high beams once, with the headlights on or off. The Automatic High Beam uses a front camera to switch between high and low beams. Among its conditions, it turns the high beams on at about 21 mph or more and off when speed drops below about 17 mph. The manual warns not to overly rely on it.

If the headlights and/or tail lights are on when the power switch is turned to OFF, the 12-volt battery-saving function turns off all the lights after approximately 20 minutes. If "Headlight System Malfunction Visit Your Dealer" appears on the multi-information display, the manual says the system may be malfunctioning; have the vehicle inspected by your Toyota dealer.

Toyota of Fox Lake hours

DepartmentHours
SalesMon-Fri 9 a.m.-9 p.m.; Sat 9 a.m.-7 p.m.; Sun closed
ServiceMon-Thu 7 a.m.-7 p.m.; Fri 7 a.m.-6 p.m.; Sat 7 a.m.-3 p.m.; Sun closed

From Toyota of Fox Lake's website, November 16, 2026. Holiday hours can differ.

Toyota Sienna headlight and bulb FAQ

What headlight bulb does a Toyota Sienna use?

None you can buy and swap yourself, for the 2026 Sienna. Toyota's 2026 Sienna owner's manual (OM08082U) lists the headlights among the lights that need to be replaced by your Toyota dealer, and says the lights other than the rear turn signal lights, back-up lights and license plate lights each consist of a number of LEDs. The manual's light bulb table lists no headlight bulb. Owners of other model years should check the manual for their Sienna.

Can I replace a Sienna headlight myself?

No, according to the manual. The only exterior lights with do-it-yourself replacement steps are the rear turn signal lights, back-up lights and license plate lights. For more information about replacing other light bulbs, the manual says to contact your Toyota dealer.

What bulbs does a 2026 Sienna use for the rear turn signal, back-up and license plate lights?

The manual's light bulb table lists WY21W, 21 W (amber wedge base) for the rear turn signal lights, W16W, 16 W (clear wedge base) for the back-up lights and W5W, 5 W (clear wedge base) for the license plate lights.

What happens if a Sienna LED light burns out?

The manual says that if any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced.

Is water inside a Sienna headlight a problem?

The manual says temporary condensation on the inside of the light lens does not indicate a malfunction. Contact your Toyota dealer if large drops of water have built up on the inside of the lens or water has built up inside the light.

What does Headlight System Malfunction mean on a Sienna?

If "Headlight System Malfunction Visit Your Dealer" appears on the multi-information display, the manual says the system may be malfunctioning. Have the vehicle inspected by your Toyota dealer.

Can Toyota of Fox Lake replace a Sienna headlight?

Yes. Our service team at 75 S US-12 in Fox Lake can inspect and replace Sienna headlights and other exterior lights. See the service hours above or schedule online.

Sources

The bulb numbers, wattage, the list of dealer-replaced lights, replacement steps, warnings and headlight operation are from Toyota's 2026 Sienna owner's manual (OM08082U), read November 16, 2026. Your own owner's manual is the final word for your vehicle. Address and hours are from Toyota of Fox Lake's own website. Photo is illustrative.

  1. Sienna 2026 Owner's Manual (OM08082U): headlight switch, daytime running lights, battery-saving function, Headlight System Malfunction message, high beams and Automatic High Beam (pp. 318-323), fuse notes and light bulbs (pp. 596-605), light bulb specifications (p. 692), Toyota, read November 16, 2026
  2. Address and sales and service hours, Toyota of Fox Lake, November 16, 2026