Owner guide · Toyota of Fox Lake · Fox Lake, IL
Toyota Sequoia Battery Guide
Where the 2026 Sequoia's 12-volt battery is, which replacement it needs, how to jump start the SUV and how to check the voltage, from Toyota's 2026 Sequoia owner's manual, read November 15, 2026.

What battery does a 2026 Toyota Sequoia use?
Toyota's 2026 Sequoia owner's manual puts the 12-volt battery in the left-hand side of the luggage compartment and calls for an LN4 case size, 80Ah or greater (20HR) and 689A or greater (CCA): a ventilation type calcium battery that conforms to European regulations and has a handle. Jump starting uses an exclusive terminal under the hood.
2026 Sequoia 12-volt battery specifications
| Item | Owner's manual says |
|---|---|
| Location | Left-hand side of the luggage compartment (slide the third seats to the frontmost position and remove the left-hand side of the luggage trim cover) |
| Replacement case size | Same as the previous battery (LN4) |
| 20-hour rate capacity (20HR) | Equivalent (80Ah) or greater |
| Performance rating (CCA) | Equivalent (689A) or greater |
| Battery type | Conforms to European regulations; ventilation type calcium battery; use a battery with a handle |
| Open voltage at 68°F (20°C) | 12.0 V or higher (turn the power switch off and turn on the high beam headlights for 30 seconds) |
| Charging rate | 5 A max. |
| Jump starting point | Exclusive jump starting terminal under the hood (open the fuse box cover, then the terminal cover) |
From Toyota's 2026 Sequoia Owner's Manual (OM0C087U), pages 591, 679-680, 682 and 699, read November 15, 2026. Check the manual that came with your vehicle.
How to jump start a Sequoia
If the 12-volt battery is discharged, the manual says you can jump start the Sequoia with jumper (or booster) cables and a second vehicle with a 12-volt battery, or call your Toyota dealer or a qualified repair shop. The steps, in short:
- Confirm that the electronic key is being carried. Depending on the situation, the alarm may activate and the doors may lock when the cables are connected.
- Open the hood and the fuse box cover.
- Open the exclusive jump starting terminal cover.
- Remove the engine cover.
- Connect a positive cable clamp to the exclusive jump starting terminal on your vehicle and the other end to the positive (+) terminal on the second vehicle. Connect a negative cable clamp to the negative (-) terminal on the second vehicle and the other end to the metallic point shown in the manual.
- Start the engine of the second vehicle, increase its engine speed slightly and hold it there for about 5 minutes to recharge your 12-volt battery.
- Open and close any of the doors of your vehicle with the power switch off.
- Keeping the second vehicle's engine speed up, start the hybrid system of your vehicle by turning the power switch to ON.
- Once the hybrid system has started, remove the cables in the exact reverse order from which they were connected, reinstall the engine cover, close the terminal cover and reinstall the fuse box cover.
The manual says to have the vehicle inspected at your Toyota dealer as soon as possible once it starts. The hybrid system cannot be started by push-starting, and the jumper cables must not become entangled in the cooling fan. To avoid igniting gas from the battery, the manual says to make sure each jumper cable is on the correct terminal, keep the other end of the cable on the + terminal away from other parts and metal surfaces such as brackets or unpainted metal, never let the + and - clamps touch, and keep smoking, matches, lighters and open flame away from the 12-volt battery. When removing the battery terminals, always remove the negative (-) terminal first.
Checking and charging the battery
From the 2026 Sequoia owner's manual:
Look at the exterior
Make sure the 12-volt battery terminals are not corroded and that there are no loose connections, cracks or loose clamps.
Check the voltage
Turn the power switch off and turn on the high beam headlights for 30 seconds before checking. The open voltage should be 12.0 V or higher at 68°F (20°C).
Charge in the open
Recharging produces flammable, explosive hydrogen gas. Always charge in an open area, not a garage or closed room without enough ventilation. If the battery is still in the vehicle, disconnect the ground cable, and keep the charger's power switch off while connecting and disconnecting its cables.
Never while running
Do not recharge the 12-volt battery while the hybrid system is operating, and turn off all accessories. The charging rate is 5 A max. After recharging, the manual says to have the battery inspected at your Toyota dealer as soon as possible.
After reconnecting
The smart key may not unlock the doors right away, so use the wireless remote control or the mechanical key. Start the hybrid system with the power switch in ACC; it may not start on the first attempt but will on the second. Then depress the brake pedal and confirm you can shift into each shift position. Information stored in the ECU is cleared and some systems may need initialization.
From Toyota's 2026 Sequoia Owner's Manual (OM0C087U) pages 591-593, 681, 684 and 699, read November 15, 2026. The manual also says to wear safety glasses, avoid sparks from tools touching the terminals and keep children away from the battery.
Replacing a Sequoia battery
Use a battery with the same case size as the one fitted. The manual says that if the sizes differ, the battery cannot be properly secured, and if the 20-hour rate capacity is low, the battery may discharge even when the SUV sits for only a short time, and the hybrid system may not be able to start. A battery without a handle is harder to remove.
Use a 12-volt battery designed for this vehicle; otherwise, the manual says, hydrogen gas may enter the passenger compartment and cause a fire or explosion. After replacing, reuse the exhaust hose that was attached to the old battery and confirm it is firmly connected to the vehicle, and fit the exhaust hole plug; if they are not properly installed, hydrogen gas may leak into the cabin and could ignite.
Removing the battery terminals clears information stored in the ECU, so the manual says to contact your Toyota dealer before removing them, turn the power switch off before disconnecting, and always remove the negative (-) terminal first. For replacement, the manual points owners to a Toyota dealer.
Toyota of Fox Lake hours
| Department | Hours |
|---|---|
| Sales | Mon-Fri 9 a.m.-9 p.m.; Sat 9 a.m.-7 p.m.; Sun closed |
| Service | Mon-Thu 7 a.m.-7 p.m.; Fri 7 a.m.-6 p.m.; Sat 7 a.m.-3 p.m.; Sun closed |
From Toyota of Fox Lake's website, November 15, 2026. Holiday hours can differ.
Toyota Sequoia battery FAQ
What 12-volt battery does the 2026 Sequoia use?
Toyota's 2026 Sequoia owner's manual calls for a 12-volt battery that conforms to European regulations, with the same case size as the previous one (LN4), a 20-hour rate capacity (20HR) equivalent to 80Ah or greater and a performance rating (CCA) equivalent to 689A or greater. It also says to use a ventilation type calcium battery with a handle.
Where is the battery on a 2026 Toyota Sequoia?
The manual says the 12-volt battery is located in the left-hand side of the luggage compartment. To reach it, slide the third-row seats to the frontmost position and remove the left-hand side of the luggage trim cover. For jump starting, the manual uses an exclusive jump starting terminal under the hood, inside the fuse box cover.
How do I jump start a Sequoia?
With jumper cables and a second vehicle with a 12-volt battery: confirm the electronic key is being carried, open the hood, the fuse box cover and the exclusive jump starting terminal cover, remove the engine cover, connect the cables as the manual shows, run the second vehicle's engine slightly faster for about 5 minutes, open and close any door with the power switch off, then start the hybrid system by turning the power switch to ON.
What voltage should a Sequoia battery have?
The manual lists an open voltage of 12.0 V or higher at 68°F (20°C), checked after turning the power switch off and turning on the high beam headlights for 30 seconds. The charging rate is 5 A max.
Can a Sequoia be push-started?
No. The manual says the hybrid system cannot be started by push-starting.
Why will my Sequoia not start after a battery change?
The manual says the hybrid system may not start on the first attempt after the 12-volt battery is reinstalled; this is not a malfunction, and it will start normally on the second attempt. The smart key may not unlock the doors right away, so use the wireless remote control or the mechanical key. If it will not start after multiple attempts, contact your Toyota dealer.
Can Toyota of Fox Lake replace my Sequoia battery?
Yes. The manual says to contact your Toyota dealer for 12-volt battery replacement. Our service team at 75 S US-12 in Fox Lake can test the battery and fit the right one for your Sequoia. See the service hours above or schedule online.
Sequoia battery weak or flat?
Bring it to Toyota of Fox Lake, 75 S US-12 in Fox Lake. Our service team can test the battery and replace it with the right one for your Sequoia.
Sources
Battery location, replacement requirements, jump start steps, charging and voltage figures are from Toyota's 2026 Sequoia Owner's Manual (OM0C087U), read November 15, 2026. Your own owner's manual is the final word for your vehicle. Address and hours are from Toyota of Fox Lake's own website. Photo is illustrative.
- 2026 Sequoia Owner's Manual (OM0C087U): 12-volt battery location, cover, charging and exterior check (pp. 591-593), jump starting, discharge and replacement requirements (pp. 679-685), electrical system specifications (p. 699), Toyota, read November 15, 2026
- Address and sales and service hours, Toyota of Fox Lake, November 15, 2026
